NXP Semiconductors
PCA9922
8-channel constant current LED driver with output error detection
7. Functional description
The PCA9922 is an 8-channel constant current LED driver with built-in LED output error
detection. The PCA9922 contains an 8-bit shift register and data latches, which convert
serial input data into parallel output data.
At the output stage, 8 regulated current sinks are designed to provide constant and
uniform current through LEDs with different forward voltages (V F ).
Refer to Figure 1 “ Block    diagram of PCA9922 ” .
7.1 System interface
During normal operation, serial data can be transferred into the PCA9922 through SDI,
shifted into the shift register, and out through the SDO. Data shifts from the SDI pin into
the next sequential bit in the shift register on each rising edge of the CLK input. The MSB
is the first bit to be clocked in. Data shifts out of the shift register and is presented on the
SDO pin on the falling edge of CLK. The exception to this is during the error detect
sequence, at which time the error status is loaded in a parallel fashion into the shift
register. The shift register is never disabled. It is either shifting or it is loading the error
status on every rising edge of CLK. Additionally, the device is designed such that it may
be cascaded with other similar devices. The SDO pin contains the output of the shift
register which may be used for cascading to the SDI pin of the next device in the series.
Data is parallel loaded from the serial shift register to an output control register when LE
(Latch Enable) is asserted HIGH (serial-to-parallel conversion). The output control register
will continue to reflect the shift register data, even if changes occur in the shift register
data, as long as LE is HIGH. When LE is LOW the latch is closed and changes in the shift
register data no longer effect the output control register. Applications where the latches
are bypassed (LE tied HIGH) will require that the OE input be HIGH during serial data
entry.
The data in the output control register is then used to drive the constant current output
drivers when the outputs are enabled. The outputs are globally enabled or disabled
through the OE. A LOW level on the OE will enable the output drivers, LED0 to LED7, to
reflect the data contained in the output control register.
An example timing diagram of expected normal operation of the device is shown in
Figure 5 .
Remark: It is recommended that OE and LE pulse widths be at least two clocks wide
when CLK is running to avoid inadvertent entry into the error detect modes.
There is no synchronization logic in the design between CLK, LE and OE. It is the user ’s
responsibility to meet the timing presented in Table 10 in order to guarantee proper
operation.
PCA9922
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 2 — 6 April 2011
? NXP B.V. 2011. All rights reserved.
6 of 27
相关PDF资料
PCA9955TW,118 IC LED DRVR CONST CURR
PCF85102C-2P/03,11 IC EEPROM 2KBIT 100KHZ 8DIP
PCF85103C-2T/00,11 IC EEPROM 2KBIT 100KHZ 8SOIC
PCF8570T/F5,512 IC SRAM 2KBIT 100KHZ 8SOIC
PCF8582C-2T/03,118 IC EEPROM 2KBIT 100KHZ 8SOIC
PCF8594C-2T/02,118 IC EEPROM 4KBIT 100KHZ 8SOIC
PCF8598C-2P/02,112 IC EEPROM 8KBIT 100KHZ 8DIP
PCU9955TW,118 IC LED DRVR CONST CURR
相关代理商/技术参数
PCA9922PW118 制造商:NXP 功能描述: 制造商:NXP Semiconductors 功能描述:
PCA9952TW,118 功能描述:LED照明驱动器 16-ch Fm+ I2C-bus 57 mA LED driver RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9952TW/Q900,118 制造商:NXP Semiconductors 功能描述: 制造商:NXP Semiconductors 功能描述:IC LED DVR 16CH I2C CC 28HTSSOP 制造商:NXP Semiconductors 功能描述:LED Lighting Drivers 16-channel Fm+ I2C- bus 57 mA LED driver
PCA9955ATW/Q900J 功能描述:LED 驱动器 IC 16 输出 线性 I2C 调光 57mA 28-HTSSOP 制造商:nxp semiconductors 系列:汽车级,AEC-Q100 包装:剪切带(CT) 零件状态:过期 类型:线性 拓扑:- 内部开关:是 输出数:16 电压 - 供电(最低):3V 电压 -?供电(最高):5.5V 电压 - 输出:20V 电流 - 输出/通道:57mA 频率:8MHz 调光:I2C 应用:背光 工作温度:-40°C ~ 85°C(TA) 安装类型:表面贴装 封装/外壳:28-SOIC(0.173",4.40mm 宽)裸露焊盘 供应商器件封装:28-HTSSOP 标准包装:1
PCA9955ATWJ 功能描述:LED 驱动器 IC 16 输出 线性 I2C 调光 57mA 28-HTSSOP 制造商:nxp semiconductors 系列:- 包装:剪切带(CT) 零件状态:过期 类型:线性 拓扑:- 内部开关:是 输出数:16 电压 - 供电(最低):3V 电压 -?供电(最高):5.5V 电压 - 输出:20V 电流 - 输出/通道:57mA 频率:8MHz 调光:I2C 应用:背光 工作温度:-40°C ~ 85°C(TA) 安装类型:表面贴装 封装/外壳:28-SOIC(0.173",4.40mm 宽)裸露焊盘 供应商器件封装:28-HTSSOP 标准包装:1
PCA9955BTW/Q900J 功能描述:LED 驱动器 IC 16 输出 线性 65mA 28-HTSSOP 制造商:nxp semiconductors 系列:- 包装:剪切带(CT) 零件状态:有效 类型:线性 拓扑:- 内部开关:是 输出数:16 电压 - 供电(最低):3V 电压 -?供电(最高):5.5V 电压 - 输出:- 电流 - 输出/通道:65mA 频率:- 调光:- 应用:汽车级,背光 工作温度:-40°C ~ 85°C(TA) 安装类型:表面贴装 封装/外壳:28-SOIC(0.173",4.40mm 宽)裸露焊盘 供应商器件封装:28-HTSSOP 标准包装:1
PCA9955BTWJ 功能描述:LED 驱动器 IC 16 输出 线性 65mA 28-HTSSOP 制造商:nxp semiconductors 系列:- 包装:剪切带(CT) 零件状态:有效 类型:线性 拓扑:- 内部开关:是 输出数:16 电压 - 供电(最低):3V 电压 -?供电(最高):5.5V 电压 - 输出:- 电流 - 输出/通道:65mA 频率:- 调光:- 应用:背光 工作温度:-40°C ~ 85°C(TA) 安装类型:表面贴装 封装/外壳:28-SOIC(0.173",4.40mm 宽)裸露焊盘 供应商器件封装:28-HTSSOP 标准包装:1
PCA9955TW,118 功能描述:LED照明驱动器 16-ch Fm+ I2C-bus 57 mA LED driver RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N